The aim of this report was to investigate if Sweden can have 100 % renewable electricity production in the year 2050. The conclusion is that it is possible but under certain conditions. For instance wave power must be in commercial use. When wind power and solar power represent a large percentage of the electric production there will be a lack of electric power during the winter but during the summer there will be a surplus of electric power. Both the surplus and the lack of electric power need to be taken into account.

Micro-power wind energy convertors have recently increased in popularity. The reasons for this are among other things the increasing cost of electric energy and enviromental concern.In this thesis the connection of these micro-power wind energy convertors to the utility network is discussed. Electric standards for the connection of small production units is presented. Finally some calculations and measurements of electric quality are also presented. The utility network used in the calculations is part of Halmstad Energi och Miljö network..

The purpose of this study is to investigate how much of the estimated annual electric energy production from Swedish wind power that actually was produced, as well as the history of this agreement over time. The aim is to also examine if there are properties that have caused some group of wind power plants to produce more or less, compared to their estimated production. Operational data on wind turbines collected by the Swedish Energy Agency was analyzed. A survey was made among owners of wind power plants with a nominal power of at least 2 MW. Two different methods for normal year correction of production data were used and compared.

The challenges facing low voltage grids are rising as an increasing number of domestic houses transition from fossil fueled heating to electricity based heating. Several environmental goals and visions have the same transition from fossil based power to electricity based power in mind for the transportation sector. One of the most important tools for this transformation is widely regarded to be the electric vehicle. With the demands of the electric vehicle pressuring the power grid, several questions arise regarding the growth of the electric vehicle market and what repercussions it may have on the grid. This paper focuses on a typical low voltage grid in southern Sweden and what effects a growing electric vehicle market may have on it. Through computer-assisted simulations based on several future scenarios regarding the EV market, this paper finds that few modifications and reinforcements are needed on this particular grid within the next 10 to 15 years.

The fishing port of Bläsinge is located on the east coast of Öland, Sweden?s second largest island. Today the port has a limited supply of freshwater. The economic association of the fishing port wants to expand their business, so that they will also include tourist services. To do this the harbor will need a more independant source of freshwater, with a higher quality than the present well.

The assignment given to us by NCC was to compose a degree project based on ground excavations for power cables. The aim of the study was to examine suitable excavation methods depending on different possible terrain conditions. The amount of previously written material within this subject is nearly non- existent and therefore there is a genuine interest by the NCC to receive a compilation of different production methods. The greater part of this study is based upon interviews with several companies active within this area of expertise. The technique of placing the electricity grid beneath ground for safety is today getting more and more common.

The purpose of the project is to determine the impact of solar cells and electrical vehicles on the future electricity grid and distribution network. Future electricity grids will be affected differently than it does today. Therefore, it is important to determine the impacts so that the current electricity distribution system can be developed and redesign to achieve the future demand. In Sweden, government has changed rules and laws in order to make it easier for private sector to invest in renewable energy sources. Our project focused on the impact of the solar cells and electric vehicles on the low voltage electricity distribution.

This degree project is an investigation of solar cells and their ability to deliver electric power as well as reducing the need for cooling. The main object of interest is a BASE-X shelter. The shelter is purchased by the Swedish Defence Materiel Administration, FMV to be used for command and camp in the new force called Nordic Battlegroup, NBG. The demand on the equipment is firstly that it should have a small weight to be easy to transport and handle and secondly to be easy to bring up fast. Therefore the choice of solar cell technology fell on thin film cells.

Today?s environmental discussions have led to more progress in the different transportareas. To ride a bicycle is often one of the most efficient alternative when it comes totransport. An Electric bike is, and makes transportation more efficient than a regularbicycle. Electric bicycles do not affect the environment significantly and allows moreconvenient transportation than ordinary bicycles do.

In this work an assessment of the compressed air system in the facilities of Vattenfall Heat Uppsala has been conducted. The facilities constitutes, among others, a combined heat and power plant, and two waste incineration plants. The compressed air is supplied primarily by seven rotary screw compressors and yearly electric energy consumption in these has been determined. Furthermore, the usage of compressed air has been mapped in order to find processes with energy savings potential. Several suggestions how to reduce the usage of compressed air have been presented, resulting in decreased need of electric energy and reduced CO2-emissions.The results show that total need of electric energy in the compressors, during a standard production year, amounts to 5.83 GWh.

This thesis is a feasibility study for a future product development project. The purpose ofthis project is to evaluate the possibilities and difficulties associated with the design of anelectric power assist servo for all terrain vehicles (ATVs). The project has been carriedout in collaboration with Nira Control AB. Nira designs and manufactures electric andelectro mechanic products mainly for the motor sport market segment.Nira Control AB is developing a fuel injection system for a new line of large ATVs oncommission. To be able to compete with manufacturers like Yamaha and Honda thecommissioner should be able to offer optional power assist steering.

During the last years commercial Wind Power Turbines (WPT) has become larger regardingto the generator sizes and hub heights. Available hub heights around 100 meters is nowcommon, which has led to profitability for WPT located in forests where there normally are tolow wind speeds. The current knowledgement regarding turbulence and the variation in thewind profile for the outcome of the power production for the WPT in forests is limited.In this Master of Science thesis an investigation concerning forest located wind power plantshas been made. The purpose has been to investigate if plants located in forest perform lesscompared to wind power turbines located at more common locations.The analyses are based on statically material for determining the availability,production/generator size, production/hub height, production/swept area and how thetopography affect the production results.The analyses show that the variation in production result for WPT located in forest comparedto turbines located at other locations is small. The availability is high and the productionresults are good..

This master thesis is a study of the Swedish hydropower capacity to balance wind power. The Swedish government has decided that it should be possible to produce 30 TWh from wind power in the year 2020. The Swedish municipalities have to have plans for wind power plants with total yearly generation of 30 TWh. Wind power is an variable energy source that needs to be balanced by other energy sources. In Sweden the Swedish hydropower can be used for balancing a large scale introduction of wind power.

This master thesis is a study of the Swedish hydropower capacity to balance wind power. The Swedish government has decided that it should be possible to produce 30 TWh from wind power in the year 2020. The Swedish municipalities have to have plans for wind power plants with total yearly generation of 30 TWh. Wind power is an variable energy source that needs to be balanced by other energy sources. In Sweden the Swedish hydropower can be used for balancing a large scale introduction of wind power.

In Uppsala CHP Plant, there are six pressure reducing valves to reduce the pressure from 15 to 3 bars, before six absorption heat pumps. During the process the energy is conserved but losses occur in form of exergy. The aim of this thesis is to reduce the losses of exergy. This can be done by letting turbines replace the pressure reducing valves.In this thesis an investigation has been done of the conditions today, the conditions after the change from pressure reducing valves to turbines and a comparison of three different types of turbine solutions. The three examined solutions are one turbine, several helical screw expanders and several small turbines in parallel with asynchronous generators.The six absorption heat pumps have been divided into two groups; one group of four and one group of two absorption heat pumps.